Search Results

Because of its outstanding efficiency, the direct-injection diesel engine is the preferred drive source in many fields. However, its emission behavior, especially with regard to particulate and nitrogen-oxide emissions, is problematic. A promising approach to reducing emissions inside the engine is presented by various (partially) homogeneous diesel combustion processes, which use suitable mixture formation and combustion management to prevent the formation of nitrogen-oxide and soot. In this paper, starting out from an ideally homogeneous combustion process with manifold injection, two further partially homogeneous combustion processes with internal mixture formation are examined. With regard to the maximum obtainable indicated mean effective pressure and the combustion noise, the ideally homogeneous combustion process proved - in the examined configuration - not to be desirable.

Natural gas as a fuel for internal combustion engines is a combustion technology showing great promise for the reduction of CO2 and particulate matter. To demonstrate the potential of natural gas direct injection, especially in combination with supercharging, some experimental investigations were carried out using a single-cylinder engine unit with lateral injector position. For this purpose different injection valve nozzles, piston crown geometries as well as operating strategies were investigated. First experimental results show that it is also possible to better support the combustion process by providing a late injection of a part of the fuel, near ignition point, so that the additional induced turbulence can speed up the flame propagation 1 Mixture formation with gaseous fuels due to its low mass density is more critical than in gasoline engines, because even high injection velocities still produce very low fuel penetration.

To demonstrate the potential of a CO2-minimized propulsion concept a study of a natural-gas, micro-hybrid powertrain was carried out. The basis was built by experimental investigations of a turbocharged 1.0-l, 3-cylinder engine operated at stoichiometric and lean air/fuel ratio with EGR and an optimized combustion strategy. With the results of this study a still existing model for micro-hybrid vehicles was filled and the CO2 emissions for several concepts were calculated. It could be shown that CO2 improvements of 30 to 40% for the IC engine and up to 50% for the complete micro-hybrid propulsion system accompanied with better driveability are possible.

The research institute FKFS in cooperation with the IVK Universität Stuttgart has recently presented QuickSim, a 3D-CFD-tool, that works integrated into the commercial 3D-CFD-code Star-CD. QuickSim has been developed to cover a vacancy in the market of simulation programs for engine development. The code introduces a new concept in the 3D-CFD-simulation of internal combustion engines (SI-Manifold-Injection and SI-GDI), that drastically reduces the CPU-time in comparison to a conventional 3D-CFD-simulation. QuickSim, as a 3D-CFD-tool, combines the advantages of local resolution of the fluid-dynamical field of internal combustion engines exactly like that provided by traditional 3D-CFD-simulations and the versatility and clearness of the real working-process analysis (WP) and of the full 1D-flow calculations. The CPU-time always remains in an acceptable range (few hours over a full operating cycle for a single-processor computing simulation).

The setting of boundary conditions on the boundaries of a 3D-CFD grid under certain conditions is a source of significant errors. The latter might occur by numerical reflection of pressure waves on the boundary or by incorrect setting of the chemical composition of the gas mixture in recirculation zones (e.g. in the intake manifold of internal combustion engines when the burnt gas from the cylinder enters the intake manifold and passes the boundary of the CDF-grid. When the flow direction is changed the setting of pure new charge on the boundary leads to errors). This type of problems should receive attention in operation points with low engine speed and load. The direct coupling of a 3D-CFD program (Star-CD) with a 1D-CFD program (GT-Power) is done by integration of the 3D-grid of the engine component as a „CFD-component” of the 1D computational model of a complete engine.

Today, mechanical systems such as the piston groups of internal combustion engines are simulated using Multiple Body-System (MBS) - approaches. However, the use of these models is restricted to a few problems as their adaptability is limited. The simulation of mechanical systems only by means of finite elements shows great promise for the future. In order to consider lubrication effects between two touching bodies of a mechanical system, a hydrodynamic contact algorithm (HCA) for finite element (FE) applications was developed. This paper discusses the technical background and first results for the simulation of a piston group using this new approach.

This paper presents a phenomenological single-zone combustion model which meets the particular requirements of high speed DI diesel engines with common rail injection. Therefore the model takes into account the freely selectable pilot and main injection and is strongly focusing on result parameters like combustion noise or NO-emission which are affected by this split injection. The premixed combustion, the mixing-controlled combustion and the ignition delay are key parts of the model. The model was developed and tested on more than 200 samples from three different engine types of DaimlerChrysler passenger car engines equipped with common rail injection. A user-friendly parameterization and a short computing time was achieved thanks to the simple structure of the model.